6.7 Rudder Pedals

There are quite a few parts that need to be put together for this assembly. It’s actually not that difficult although there are a few tricks that I needed to learn, especially in areas where the manual wasn’t as clear as it could be. Also, I decided to paint the main metal assembly before putting it all together. The steel pipes, as sent from the factory, just had some gray primer on them. I spray painted my assembly a nice, shiny black which I think looks much better.

Fuselage - Brake and Rudder Pedal Assembly Parts

Here are all of the parts for the rudder pedal assembly. I pre-painted the main mechanism black.

The gold-colored assemblies are Matco brake cylinders, one for the left brake and one for the right. Spacing is critical so that the cylinders don’t rub against the steel brackets. That’s why you’ll see quite a few washers between the top of the cylinder attachment point and the metal bracket.

Fuselage - Brake and Rudder Pedal Assembly - Attaching Brake Cylinders

Two brake cylinders attached!

Fuselage - Brake and Rudder Pedal Assembly - Pilot Side

Pedals and cylinders attached on the pilot's side!

Fuselage - Brake and Rudder Pedal Assembly - Co-pilot's side

And here everything is attached on the co-pilot's side!

As with everything, before the assembly is attached to the canard bulkhead, it has to be leveled. Before doing that I rechecked the level of the fuselage itself. I then needed to come up with a method to level the assembly (which is a bit heavy and awkward to handle) before drilling the holes and attaching it to the bulkhead. Sometimes simple is the best, so I grabbed a board and some tie wraps and used those tie wraps to level it, one “click” at a time. I also needed to set the clearance properly between the assembly and the top of the keel. Since the assembly itself is made out of steel, it made it really easy to magnetically attach my digital level to the center of the assembly for leveling. I don’t show that in the photo below, but trust me, it worked well!

Fuselage - Leveling the Brake and Rudder Pedal Assembly

Once the fuselage is re-leveled, I then came up with this simple contraption to level the assembly before the final install.

Before attaching the rudder and brake pedal assembly I need to prepare the rudder bell crank assembly which gets attached to a protrusion pre-molded into the canard bulkhead at the factory. Two large holes are drilled at the appropriate places to let the torque rods pass through. The bell crank itself is shown attached to its bracket below, and that bracket is also attached to the bulkhead. The bell crank locks the two pedals together so that when the left pedal is pushed in, the right pedal is automatically pushed out, and vice versa. Only one rudder is deployed at a time using this connection method. (Older Velocity’s didn’t use this bell crank and therefore, both pedals could be pushed at the same time, creating a speed brake effect. Velocity’s now come with a speed brake so the old rudder pedal method is no longer used.)

Fuselage - Rudder Pedal Bellcrank - Opposite Side

And here we see the bell crank (sort of) from the inside of the fuselage.

Fuselage - Rudder Pedal Bellcrank

The bell crank locks the two pedals together so that they move in opposite directions.

Finally, the brake fluid reservoir gets installed. The manual is very non-specific about where to install this. It just suggests to pick a good location that’s easy to get to, especially when bleeding the brake system. I decided to make some brackets and install it in the nose close to the nose access cover. That should give me great access for bleeding the system without making too much of a mess!

Fuselage - Brake Cylinder Reservoir Bracket

Here's one bracket to be used for attaching the brake cylinder reservoir. The clamp is holding it in place while the epoxy cures.

Fuselage - Brake Cylinder Reservoir Bracket (1)

Here's the completed assembly.

Fuselage - Brake Cylinder Reservoir Bracket (2)

And here's a 2nd view showing the secondary bracket for strengthening.

I had to leave room for the battery, which gets installed on the shelf at the bottom right of the photo. That’s why the brake lines swoop around towards the side of the fuselage. The brake lines pass through the canard bulkhead via some rubber grommets to provide protection and to make it easier for those brake lines to move as the pedals are operated.

And that concludes the installation of the rudder and brake pedal assembly. It turned out to be one of the easier assemblies to install. In Section 6.8 I’ll show how the parking brake valve is installed as well as the long brake lines that run the length of the fuselage back to the main gear assembly.

ui© John Trautschold 2018